Monthly Archives: November 2022

My home-made brandy and still.

Leave a reply
MY home-made still, and messy lab. Note the masking tape seal and the nylon hoses. Nylon is cheaper than copper. The yellow item behind the burner is the cooling water circulation pump. The wire at top and left is the thermocouple.

I have an apple tree, a peach tree, and some grape vines. They’re not big trees, but they give too much fruit to eat. The squirrels get some, and we give some away. As for the rest, I began making wine and apple jack a few years back, but there’s still more fruit than I can use. Being a chemical engineer, I decided to make brandy this year, so far only with pears and apples.

The first steps were the simplest: I collected fruit in a 5 gallon, Ace bucket, and mashed it using a 2×4. I then added some sugar and water and some yeast and let it sit with a cover for a week or two. Bread yeast worked fine for this, and gives a warm flavor, IMHO. A week or so later, I put the mush into a press I had fro grapes, shown below, and extracted the fermented juice. I used a cheesecloth bag with one squeezing, no bag with the other. The bag helped, making cleanup easier.

The fruit press, used to extract liquid. A cheese cloth bag helps.

I did a second fermentation with both batches of fermented mash. This was done in a pot over a hot-plate on warm. I added more sugar and some more yeast and let it ferment for a few more days at about 78°F. To avoid bad yeasts, I washed out the pot and the ace bucket with dilute iodine before using them– I have lots of dilute iodine around from the COVID years. The product went into the aluminum “corn-cooker” shown above, 5 or 6 gallon size, that serves as the still boiler. The aluminum cover of the pot was drilled with a 1″ hole; I then screwed in a 10″ length of 3/4″ galvanized pipe, added a reducing elbow, and screwed that into a flat-plate heat exchanger, shown below. The heat exchanger serves as the condenser, while the 3/4″ pipe is like the cap on a moonshiner still. Its purpose is to keep the foam and splatter from getting in the condenser.

I put the pot on the propane burner stand shown, sealed the lid with masking tape (it worked better than duct tape), hooked up the heat exchanger to a water flow, and started cooking. If you don’t feel like making a still this way, you can buy one at Home Depot for about $150. Whatever route you go, get a good heat exchanger/ condenser. The one on the Home-depot still looks awful. You need to be able to take heat out as fast as the fire puts heat in, and you’ll need minimal pressure drop or the lid won’t seal. The Home Depot still has too little area and too much back-pressure, IMHO. Also, get a good thermometer and put it in the head-space of the pot. I used a thermocouple. Temperature is the only reasonable way to keep track of the progress and avoid toxic distillate.

A flat-plate heat exchanger, used as a condenser.

The extra weight of the heat exchanger and pipe helps hold the lid down, by the way, but it would not be enough if there was a lot of back pressure in the heat exchanger-condenser. If your lid doesn’t seal, you’ll lose your product. If you have problems, get a better heat exchanger. I made sure that the distillate flows down as it condenses. Up-flow adds back pressure and reduces condenser efficiency. I cooled the condenser with water circulated to a bucket with the cooling water flowing up, counter current to the distillate flow. I could have used tap water via a hose with proper fittings for cooling, but was afraid of major leaks all over the floor.

With the system shown, and the propane on high, it took about 20 minutes to raise the temperature to near boiling. To avoid splatter, I turned down the heater as the temperature approached 150°F. The first distillate came out at 165°F, a temperature that indicated it was not alcohol or anything you’d want to drink. I threw away the first 2-3 oz of this product. You can sniff or sip a tiny amount to convince yourself that this this is really nasty, acetone, I suspect, plus ethyl acetate, and maybe some ether and methanol. Throw it away!

After the first 2-3 ounces, I collected everything to 211°F. Product started coming in earnest at about 172°F. I ended distillation at 211°F when I’d collected nearly 3 quarts. For my first run, my electronic thermometer was off and I stopped too early — you need a good thermometer. The material I collected and was OK in taste, especially when diluted a bit. To test the strength, I set some on fire, the classic “100% proof test”, and diluted till it to about 70% beyond. This is 70% proof, by the classic method. I also tried a refractometer, comparing the results to whiskey. I was aiming for 60-80 proof (30-40%).

My 1 gallon aging barrel.

I tried distilling a second time to improve the flavor. The result was stronger, but much worse tasting with a loss of fruit flavor. By contrast, a much better resulted from putting some distillate (one pass) in an oak barrel we had used for wine. Just one day in the barrel helped a lot. I’ve also seen success putting charred wood cubes set into a glass bottle of distillate. Note: my barrel, as purchased, had leaks. I sealed them with wood glue before use.

I only looked up distilling law after my runs. It varies state to state. In Michigan, making spirits for consumption, either 1 gal or 60,000 gal/year, requires a “Distilling, Rectifying, Blending and/or Bottling Spirits” Permit, from the ATF Tax and Trade Bureau (“TTB”) plus a Small Distiller license from Michigan. Based on the sale of stills at Home Depot and a call to the ATF, it appears there is little interest in pursuing home distillers who do not sell, despite the activity being illegal. This appears similar to state of affairs with personal use marijuana growers in the state. Your state’s laws may be different, and your revenuers may be more enthusiastic. If you decide to distill, here’s some music, the Dukes of Hazard theme song.

Robert Buxbaum, November 23, 2022.

The main building block of Alzheimer’s research was faked. Now, what.

4 Replies

Much of health research is a search for simple, bio-molecular causes for our medical problems. These can result in pill-solutions. Diseases tend to be more complex, but Alzheimers seemed to work that way, until this summer when it turned out that the data supporting the simple theory was faked. Alzheimer’s is a devastating cognitive disease that is accompanied by a degenerating brain, with sticky, beta-amyloid plaques and tangles. About 16 years ago, this report, published in Nature seemed to show that a beta-amyloid, Aβ*56, caused the plaques and caused cognitive decline independent of any other Alzheimers indicators. 

The visual difference between an Alzheimer brain and a normal brain is that the former has shrunk. Maybe fat is relevant, fat body leads to a fat brain, and less AZ, maybe?

We were on the way to a cure, or so it seemed. Several studies by this group backed the initial results, and much of Alzheimer’s research was directed into an effort to fill in the story, and find ways to reduce the amount and bonding of this amyloid and others like it. Several other groups claimed they could not find the amyloid at all, or show that amyloids caused the symptoms described. But most negative results went unpublished. The theory was so satisfying, and the evidence from a few so strong, that the NIH poured billions into this approach, over $1B in this year alone. The FDA approved aducanumab, a drug from Biogen, on the assumption that it should work, even though it showed little to no benefit, and had some deadly side effects. Other firms followed, asking for approval of related anti-amyloid drugs that should work.

When news of the fraud came out, detected by Matthew Scragg and a few lone curmudgeons, stock prices plummeted in the drug companies. It now appears that the original work was made up, presented to journals and to the NIH using photoshopped images. For the group that did the fake work, it may mean jail time, for most other groups, the claim is that their work is still relevant. Doctors still prescribe the medications as they have nothing better to offer (Aducanumab therapy costs $50,000 per year). Maybe it’s time to start looking at alternative approaches and theories, sidelined over the last 16 years.

Some alternative theories posit that another molecule is responsible, particularly tau, associated with the tangles. Another sidelined theory is that amyloids are good. For example, that it’s the loss of soluble amyloids that causes Alzheimer’s. Alternately, that inflammation is the root cause, and that the amyloid plaques and tangles are a response to the inflammation, a bandage, perhaps. These theories could explain why the anti-amyloid drugs so often resulted in patient death.

It could be that high bmi protects from dementia. Either that or the diseases that cause weight loss cause dementia. It’s debated here.

It’s also possible that the inability of nerve cells to dispose of waste is the cause of AZ. In heathy people, waste is removed through acidic enzymes within lysosomes. Patients with decreased acid activity have a buildup of waste that includes amyloids. Perhaps the cure is to restore the acid enzymes.

My favorite theory is based on statistical data that shows that fat people are less likely to develop Alzheimers. This might lead to a junk-food cure. The fitness industry is very much against this theory–It’s debated here. They tend to support the inflammation model, claiming that diseases cause Alzheimer’s and cause patients to loose weight first. Could be. I note that Henry Kissinger is the only active politician of my era, the early 70s, still alive and writing intelligently.

Robert Buxbaum, November 17-19, 2022. I hope that Matthew Schragg comes out OK, by the way. Ben Franklin pointed out, that “No good deed goes unpunished.”

Transparent, super wood

Leave a reply

As mentioned in a previous post, wood is more among the strongest materials per unit weight, making it ideal for table tops and telephone polls. On a per pound basis, most species of wood are more than twice as strong as aluminum or mild steel. Wood’s structure is is the reason; it’s a natural composite of air-filled, aligned tubes of crystalline cellulose, held together by natural glue, lignin.

In terms of raw strength though, pounds/in2, wood is not particularly strong, only about 7000 psi (45MPa) both in tension and compression, about half the strength of aluminum. It is thus not well suited to supporting heavy structures, like skyscrapers. (I calculate the maximum height of a skyscraper here), but wood can be modified to make it stronger by removing most of the air, and replacing it with plastic. The result is a stronger, denser, flexible composite, that is typically transparent. The flower below is seen behind a sheet of transparent wood.

A picture of a flower taken through a piece of transparent super-wood.

To make a fairly strong, transparent wood, you take ordinary low-density wood (beech or balsa are good) and soak it in alkali (NaOH). This bleaches the wood, softens the cellulose, and dissolves most of the lignin. You next wash off the alkali and soak the wood in a low viscosity epoxy or acrylic. Now, put it in a vacuum chamber to remove the air — you’ll need a brick to hold the wood down in the liquid. You’ll see bubbles in the epoxy as the air leaves. Then, when the vacuum is released, the wood soaks up the epoxy or acrylic. On curing, you get a composite strong and transparent, but not super strong.

To make the wood really strong, super-strong, you need to compress the uncured, epoxy soaked wood. One method is to put it in a vice. This drives off more of the air and further aligns the cellulose fibers. You now cure it as before (you need a really slow cure epoxy or a UV-cure polymer). The resultant product have been found to have tensile strengths as high as 270 MPa in the direction of alignment, over 40,000 psi. This is three times stronger than regular aluminum, 90 MPa, (13,500 psi). It’s about the strength of the strongest normal aluminum alloy, 6061. It’s sort of expensive to make, but it’s flexible and transparent, making it suitable for space windows and solar cells. It’s the lightest flexible transparent material known. It’s biodegradable, and that’s very cool, IMHO. See here for a comparison with other, high strength, transparent composites.

Robert Buxbaum, November 10, 2022. I think further developments along this line would make an excellent high school science fair project, college thesis, or PhD research project. Compare different woods, or epoxies, different alkalis, and temperatures, or other processing ideas. How strong and transparent can you make this material, or look at other uses. Can you use it for roof solar cells, like Musk’s but lighter, or mold it for auto panels, it’s already lighter and stronger, or use it as bullet-proof glass or airplane windows.

Is the right the source of antisemitism in America.

3 Replies

Hillary Clinton famously called Trump supporters “a basket of deplorables” and went on to explain that half of them were “unredeemable”, Nazis and Klansmen, while the other half “needed reeducation.” Her statement was applauded on the left, and taken as an insult on the right. To this day, Biden and his group make the claim that Republicans are antisemites and a threat to American democracy. The proof here is a 2017 video of Klansmen carrying torches, saying “Jews will not replace us,” as they protested the removal of a statue of Robert E. Lee in Virginia. A further claim is that the rise in antisemitic incidents, shootings, beatings, etc., are the result of Trump and the Republicans. Things are not quite so black and white, or course, e.g. during the ANTIFA protests/riots four synagogs were attacked in LA alone, and the Crown-Heights neighborhood of Brooklyn was torched. Many of the attackers of Jews have Islamic names and left association, things that don’t suggest Republicans but Democrats.

CNN has claimed that the difference is intent: Trump’s intent is evil, while ANTIFA’s is to elevate black and Moslem lives by allowing them to vent their righteous anger (on Jews). The Moslems who attacked Jews in Monsey, India, Paris and elsewhere are acting for justice, while the marchers in Charlottesville march for hate. In a special program on “Antisemitism in American”, CNN made the claim that no Jew should support the Republicans or Jewish Israel, an apartheid, colonial occupation in their view. This appears to be the view of the Biden White House too. They have yet to congratulate the winner of Israeli presidential elections, 5 days after the election. They contacted Mahmoud Abbas, the Palestinian leader instead, to discuss joint efforts to enhance Palestinian security. Obama did the same, seven years ago, not congratulating the Israeli election winner (Netanyahu), and snubbed the Israeli delegation on their visit, leaving them to sit alone without food or photographs.

According to the CNN expert on Antisemitism, the lefts’ dismissal of Israel’s leaders is because European Jews are not Jews at all, but Russians with no connection to the land. To my thinking claims like this against a group’s identity are horribly hurtful — CNN’s expert was claiming, essentially, that the jews were lying about everything since the beginning. If Jews are not from Israel, why have we prayed in that direction for return, and in the language of that land. If we did not build the old synagogs, when did we displace the builders and take over their language and culture? Attacks on Jewish identity are more serious, in my mind, than any march for Robert E. Lee. (I’ve written in favor of the peace hammered out between Grant and Lee).

Perhaps even more damaging is the left’s attack on Jewish education. The New York Times ran three-page article claiming that Jewish education abuses the students by not teaching real science or history, and by enforcing religious and sexual norms that are counter to the children’s rights — rights that include LGBQT+ expression. While it is true that Jewish education is not a fan of LGBQT+, but neither is Moslem education, or Catholic, or Mormon. Education is how a culture survives. Some Catholic leaders have noted that they have a stake in this.

The left is anti Israel and anti Jewish education, yet claims to be the defenders of Jews because they can’t stand Trump.

Speaking of survival, about half of all Jews now live in Israel, a state established by the UN in 1947 in part as a response to the mass murder of Jews in Europe. Along with Europeans, about half of the Israelis today are exiles from communities wiped out by Moslem governments: from Egypt, Tunisia, Iran, Iraq, Turkey, and Yemen. If Israel becomes Islamic as Obama favored, they are likely to exile all the Jews as they did in 1968 in Jerusalem, and as the surrounding countries have done. Where would the Jews go? It’s not a problem for Obama-Biden, but it’s a survival problem for Israelis. My sense is that the left is, by far, the more antisemitic, both in terms of culture and physical safety.

Robert Buxbaum, November 7, 2022